Microsetcontrols
Microsetcontrols
home contact us sitemap
Microsetcontrols
 
ph-meters Microsetcontrols
 

Dissolved Chlorine Di Oxide Sensor Manufacturers - MicroSet Controls, India

Microsetcontrols
 
products-1 Microsetcontrols
 

Dissolved Chlorine Di Oxide Sensors

 
Dissolved Chlorine Di Oxide Sensors Microsetcontrols
 
 
With the exception of the 4-20mA sensors, where the length is 220mm, the sensors have a length of 175mm and a diameter of 25mm, with plug adaptor connection.
They are designed to fit into the available flow cells.
The low current produced by the sensors is electronically amplified in the measurement cell.
No zero point calibration is necessary, and measurements can be taken in pressure up to 1 BAR.
The sensors are temperature compensated, and will operate in the range 0 to 45 degrees C (for the 7 Series, 0-55).
The water has to be flowing to obtain a reading, which is why flow cells are recommended.
Changes to the minimum flow rate will only slightly affect the measurement signal.
Surfactants should not be present in the water being measured (does not apply to the 7 Series probes).
For the dual electrode system, the measurement cell is made of gold, and the counter and reference electrodes of silver with silver halogenid coating. A bias voltage (polarisation) is applied between the two electrodes.
For the potentiostatic 3 electrode system, the measurement electrode is made of gold, the reference electrode is made of silver with a silver halogenid coating, and the counter electrode of stainless steel.
 
 
Ms CL52 - Application: Free Chlorine, Inorganic Chlorine
Cannot measure with Cyanuric Acid present
Ms CL52 - Application: Free Chlorine, Inorganic Chlorine Microsetcontrols
 
 
• Amperometric Two and Three electrode systeMs with replacement membranes.
• 30/40 L/h Flow rate required.
• 1 Bar permissible pressure
• Single point calibration
• Sample must be free of surfactants
 
 
SPECIFICATION
 
4 Pole Sensors
Range
N
:
0.05 – 20 ppm
  H
:
0.005 – 2 ppm
Resolution N
:
0.01ppm
  H
:
0.001ppm
Slope N
:
-100 mV/ppm
  H
:
-1000 mV/ppm
pH Range  
:
4 - 8 pH
No. of Electrodes  
:
2
Membrane Cap  
:
M20
 
 
2 Pole Sensors for 4-20mA Instruments
Range MA0.5
:
0 - 0.5 ppm
  MA2
:
0 - 2 ppm
  MA5
:
0 - 5 ppm
  MA10
:
0 -10 ppm
  MA20
:
0 -20 ppm
Resolution  
:
0.01 ppm
pH Range  
:
4 - 8 pH
No. of Electrodes  
:
2
Membrane Cap  
:
M20
 
 

• Handling, commissioning and service are extremely easy. The electrode system has a very long working life, with just the    membrane cap subject to wear and tear. This needs to be replaced every year. However, maintenance costs are very low.
• The time needed to polarise most of the probes is less than 2 hours.
• No zero point calibration is necessary, and it is only necessary to have a single point calibration, only a slope test is required.
• Because the flow dependence is so low, various in-line probe housings can be used, and it is possible to fit "in-line".
• For most of the probes it is possible to operate up to 1 Bar (higher on request), and this enables the water to be easily returned.
• Temperature compensation is integrated in every probe.
• 90% of the final value of the measurement can be reached in less than 2 minutes formost measurement probes.
• Long term stability is excellent, slope loss is approximately 1% per month.
• Due to low impedance of the probes, long cables can be used without probleMs.
• Because the probes are available with different ranges, and power supplies, theyc an be used with a customers existing    controllers.

 
 
request Microsetcontrols
pdf-button Microsetcontrols
 
line Microsetcontrols
           
   
Microsetcontrols
Microsetcontrols
Microsetcontrols  
   
 
Home

About us

Contact us

Enquiry

Sitemap
 
 
     
Industrial pH Sensor Ms pH 01 / Ms pH 02 / Ms pH 04, Ms pH 07, • pH Sensor – Industrial – HF Series Ms pH 22 / HF / Pt 100, • Industrial pH Sensor - Ms pH 36 – Flat (Origin USA), • pH Indicator Ms pH 19, • pH Controller Ms pH 27 / Ms pH 27 W, • pH Transmitter Ms pH 27 B / Ms pH 18 T, • Lab / Bench Meter Ms pH 616 / Ms pH 644, Ms 324 / Ms pH 816 / Ms 9535, • pH Sensor Housing for Fermentor Model 330, • pH Flow Cell, • Industrial ORP Sensor with Platinum Tip Ms ORP 01 / Ms ORP 02 / Ms ORP 36, • ORP Indicator Ms ORP 19, • ORP Controller Ms ORP 27 Panel Mounted, • ORP Controller Ms ORP 27 W Field Mounted
 
MICROSET CONTROLS
Microsetcontrols
:
B 404, Marvel Imperial, FP No 260/2&3, Narangibaug Road, Boat Club Area,
Pune - 411 001. Maharashtra, INDIA.
Microsetcontrols
:
Microsetcontrols
:


MICROSET CONTROLS
 

Microsetcontrols